Pumps - cased pumps

700 series cased pump

Overview

730 series process pumps

730SN, 730UN, 730DuN and 730BpN peristaltic process pumps fitted with continuous tubing or tube element pumpheads.

730 series process pumps offer four drive options, colour display and intuitive menu structures that provide visual status indication and minimal key presses.

Pumphead options available as standard (others available on request):

  • 720R single pumphead for continuous tubing
  • 720RE single pumphead for tube elements
  • 720RX and 720REX extension twin pumpheads

Features and benefits

  • Colour display and intuitive menu structures provide visual status indication and minimal key presses
  • Flow rates from 0.12 L/h (0.03 USGPH) to 3,300 L/h (872 USGPH)
  • 3,600:1 speed control range from 0.1 to 360 rpm in 0.1 rpm increments
  • Keypad incorporates 3-level security PIN lock
  • IP66 (NEMA 4X) cased pumps
  • Dual voltage 115/230 V 50/60 Hz
  • Remote Analogue/Digital, RS485, PROFIBUS®, PROFINET®, SCADA and EtherNet/IP™ control options

Technical summary

Max. flow rate3300 L/h
Min. flow rate0.12 L/h
Max. flow rate872 USGPH
Min. flow rate0.03 USGPH
Drive speed control ratio3600:1 
Operating temperature range5 - 40 °C
Operating temperature range40 - 104 °F
Control typesEtherNet/IP™, Profibus®, Profinet®, Remote Analogue/Digital, RS485, SCADA 
Drive standardsCE, cETLus, C-Tick, IRAM, NSF/ANSI 61 (for Marprene tubing and loadsure elements) 
Drive ingress ratingIP66, NEMA 4X 
Drive power supply100-120 V/200-240 V 1ph 50/60 Hz 350 VA 
Compatible tubing bore size 9.6, 12.7, 15.9, 19, 25.4 mm

Technical Summary table lists features available within the range. See ‘Technical specifications’ tab for model specific information.

Performance

Drive with 720R Pumphead performance

720R four-roller pumpheads for continuous 4.8 mm wall thickness tubing — Tube bore and flow rates — L/h (USGPH)
720R single pumpheads 0.25 bar (3.6 psi) 0.5 bar (8 psi) 1 bar (15 psi) 1.5 bar (22 psi) 2 bar (30 psi)
Max speed (rpm)* Max flow Max speed (rpm)* Max flow Max speed (rpm)* Max flow Max speed (rpm)* Max flow Max speed (rpm)* Max flow
9.6 mm (0.4") 360 420 (111) 360 420 (111) 360 420 (111) 360 420 (111) 360 420 (111)
12.7 mm (0.5") 360 780 (206) 360 780 (206) 360 780 (206) 360 780 (206) 360 780 (206)
15.9 mm (0.6") 360 1100 (291) 360 1100 (291) 360 1100 (291) 360 1100 (291) 300 900 (238)
19.0 mm (0.7") 360 1500 (396) 360 1500 (396) 360 1500 (396) 300 1300 (343) 250 1000 (264)
25.4 mm (1.0") 360 2000 (528) 360 2000 (528) 360 2000 (528) 200 1100 (291)

*The maximum speed is reduced at increased discharge pressures to ensure safe running of the pump

Drive with 720RE Pumphead performance

720RE four-roller pumpheads for LoadSure elements — Tube bore and flow rates — L/h (USGPH)
720RE single pumphead 0.25 bar (3.6 psi) 0.5 bar (8 psi) 1 bar (15 psi) 1.5 bar (22 psi) 2 bar (30 psi)
Max speed (rpm)* Max flow Max speed (rpm)* Max flow Max speed (rpm)* Max flow Max speed (rpm)* Max flow Max speed (rpm)* Max flow
9.6 mm (0.4") 360 420 (111) 360 420 (111) 360 420 (111) 360 420 (111) 360 420 (111)
12.7 mm (0.5") 360 780 (206) 360 780 (206) 360 780 (206) 360 780 (206) 360 780 (206)
15.9 mm (0.6") 360 1100 (291) 360 1100 (291) 360 1100 (291) 360 1100 (291) 300 900 (238)
19.0 mm (0.7") 360 1500 (396) 360 1500 (396) 360 1500 (396) 300 1300 (343) 250 1000 (264)
25.4 mm (1.0") 360 2000 (528) 360 2000 (528) 360 2000 (528) 200 1100 (291)

*The maximum speed is reduced at increased discharge pressures to ensure safe running of the pump

Drive with 720R/RX Pumphead performance

720RX four-roller extension pumpheads for continuous 4.8 mm wall thickness tubing — Tube bore and flow rates — L/h (USGPH)
720R/RX twin pumpheads 0.25 bar (3.6 psi) 0.5 bar (8 psi) 1 bar (15 psi) 1.5 bar (22 psi) 2 bar (30 psi)
Max speed (rpm)* Max flow Max speed (rpm)* Max flow Max speed (rpm)* Max flow Max speed (rpm)* Max flow Max speed (rpm)* Max flow
9.6 mm (0.4") 300* 700 (185) 300* 700 (185) 300* 700 (185) 250 590 (156) 200 470 (124)
12.7 mm (0.5") 300* 1300 (343) 300* 1300 (343) 250 1100 (291) 200 870 (230) 175 760 (201)
15.9 mm (0.6") 300* 1800 (476) 200 1200 (317) 175 1100 (291)
19.0 mm (0.7") 300* 2500 (660) 200 1700 (449) 160 1390 (367)
25.4 mm (1.0") 300* 3300 (872) 200 2200 (581)

*The maximum speed is reduced at increased discharge pressures to ensure safe running of the pump

Drive with 720RE/REX Pumphead performance

720REX four-roller extension pumpheads for LoadSure elements — Tube bore and flow rates — L/h (USGPH)
720RE/REX twin pumpheads 0.25 bar (3.6 psi) 0.5 bar (8 psi) 1 bar (15 psi) 1.5 bar (22 psi) 2 bar (30 psi)
Max speed (rpm)* Max flow Max speed (rpm)* Max flow Max speed (rpm)* Max flow Max speed (rpm)* Max flow Max speed (rpm)* Max flow
9.6 mm (0.4") 300* 700 (185) 300* 700 (185) 300* 700 (185) 250 590 (156) 200 470 (124)
12.7 mm (0.5") 300* 1300 (343) 300* 1300 (343) 250 1100 (291) 200 870 (230) 175 760 (201)
15.9 mm (0.6") 300* 1800 (476) 200 1200 (317) 175 1100 (291)
19.0 mm (0.7") 300* 2500 (660) 200 1700 (449) 160 1390 (367)
25.4 mm (1.0") 300* 3300 (872) 200 2200 (581)

*The maximum speed is reduced at increased discharge pressures to ensure safe running of the pump

Specifications

Technical specifications

Drive with 720R PumpheadDrive with 720RE PumpheadDrive with 720R/RX PumpheadDrive with 720RE/REX Pumphead
Compatible tubing bore size 9.6, 12.7, 15.9, 19, 25.4 mm9.6, 12.7, 15.9, 19, 25.4 mm9.6, 12.7, 15.9, 19, 25.4 mm9.6, 12.7, 15.9, 19, 25.4 mm
Compatible tubing wall thickness 4.8 mm4.8 mm4.8 mm4.8 mm
Drive control optionsBpN, DuN, DuS, EnN, PnN, SN, UN, US BpN, DuN, DuS, EnN, PnN, SN, UN, US DuN, DuS, EnN, PnN, SN, UN, US DuN, DuS, EnN, PnN, SN, UN, US 
Drive ingress ratingIP66, NEMA 4X IP66, NEMA 4X IP66, NEMA 4X IP66, NEMA 4X 
Drive noise85dB(A) at 1m 85dB(A) at 1m 85dB(A) at 1m 85dB(A) at 1m 
Drive power supply100-120 V/200-240 V 1ph 50/60 Hz 350 VA 100-120 V/200-240 V 1ph 50/60 Hz 350 VA 100-120 V/200-240 V 1ph 50/60 Hz 350 VA 100-120 V/200-240 V 1ph 50/60 Hz 350 VA 
Drive speed control ratio3600:1 3600:1 3600:1 3600:1 
Drive speed 0.1 - 360 rpm0.1 - 360 rpm0.1 - 360 rpm0.1 - 360 rpm
Drive standardsCE, cETLus, C-Tick, IRAM, NSF/ANSI 61 (for Marprene tubing and loadsure elements) CE, cETLus, C-Tick, IRAM, NSF/ANSI 61 (for Marprene tubing and loadsure elements) CE, cETLus, C-Tick, IRAM, NSF/ANSI 61 (for Marprene tubing and loadsure elements) CE, cETLus, C-Tick, IRAM, NSF/ANSI 61 (for Marprene tubing and loadsure elements) 
Drive weight 18.5 kg18.5 kg18.5 kg18.5 kg
Drive weight 40.8 lbs40.8 lbs40.8 lbs40.8 lbs
Pumphead number of channels
Pumphead number of rollers
Control typesEtherNet/IP™, Profibus®, Profinet®, Remote Analogue/Digital, RS485, SCADA EtherNet/IP™, Profibus®, Profinet®, Remote Analogue/Digital, RS485, SCADA EtherNet/IP™, Profibus®, Profinet®, Remote Analogue/Digital, RS485, SCADA EtherNet/IP™, Profibus®, Profinet®, Remote Analogue/Digital, RS485, SCADA 
Drive humidity(Non-condensing) 80 % up to 31 °C (88 °F) decreasing linearly to 50 % at 40 °C (104 °F) (Non-condensing) 80 % up to 31 °C (88 °F) decreasing linearly to 50 % at 40 °C (104 °F) (Non-condensing) 80 % up to 31 °C (88 °F) decreasing linearly to 50 % at 40 °C (104 °F) (Non-condensing) 80 % up to 31 °C (88 °F) decreasing linearly to 50 % at 40 °C (104 °F) 
Max. altitude2000 2000 2000 2000 
Max. flow rate2000 L/h2000 L/h3300 L/h3300 L/h
Max. flow rate528 USGPH528 USGPH872 USGPH872 USGPH
Min. flow rate0.12 L/h0.12 L/h0.12 L/h0.12 L/h
Min. flow rate0.03 USGPH0.03 USGPH0.03 USGPH0.03 USGPH
Operating temperature range5 - 40 °C5 - 40 °C5 - 40 °C5 - 40 °C
Operating temperature range40 - 104 °F40 - 104 °F40 - 104 °F40 - 104 °F
Weight25 kg25 kg31.5 kg31.5 kg
Weight55.1 lbs55.1 lbs69.4 lbs69.4 lbs

Drive with 720R Pumphead dimensions

Dimension A
720R 279 mm (11")

Drive with 720RE Pumphead dimensions

Dimension A
720RE 314 mm (12.4 ")

Drive with 720R/RX Pumphead dimensions

Dimension A
720RX 279 mm (11")

Drive with 720RE/REX Pumphead dimensions

Dimension A
720REX 314 mm (12.4 ")

Materials of construction

Drive casework coatingAlocrom pre-treatment, Exterior grade polyester powder coat
Drive shaftStainless steel 440C
Drive keypad/HMIPolyester
Drive rear blanking plateStainless steel 316
Pumphead body assemblyAluminium
Pumphead roller assemblyMoS2 filled Nylon 6 (Nylatron)
Pumphead rotor assemblyAluminium, Stainless steel
Pumphead trackAluminium
Guide roller assemblyMoS2 filled Nylon 6 (Nylatron)
Pumphead front/back platesAluminium
SpindlesStainless steel
SpringsStainless steel
Switch-plateABS PA-765

Information listed covers the complete range. For detailed specifications of individual models/components refer to user manual or contact WMFTS representative.

Control

Control options

Key to pump drive models
730SN 730UN 730DuN 730BpN 730US 730DuS 730EnN 730PnN
Standard IP66 / NEMA 4X Universal IP66 / NEMA 4X Digital Universal IP66 / NEMA 4X Bus Pump / Profibus IP66 / NEMA 4X Universal SCADA / IP66 / NEMA 4X Digital Universal SCADA / IP66 / NEMA 4X EtherNet/IP / IP66 / NEMA 4X PROFINET® / IP66 /NEMA 4X
Manual control
Pump drives 730SN 730UN 730DuN 730BpN 730US 730DuS 730EnN 730PnN
Intuitive keypad and colour display
Choice of flowrate or speed display
Full calibration with choice of flow units
MemoDose function
Auto restart facility
Guard switch detection
Leak detection
Dipensing (Network Control)
Remote control
Pump drives 730SN 730UN 730DuN 730BpN 730US 730DuS 730EnN 730PnN
Configurable start/stop, leak detector and pressure switch input (via contact closure or 5 V TTL to 24 V)
Configurable start/stop, leak detector and pressure switch input (via 110 V industrial logic)
Direction change and auto/manual toggle input (via contact closure or 5 V TTL to 24 V)
Direction change and auto/manual toggle input (via 110 V industrial logic)
Remote operation of MemoDose (foot/hand-switch or logic input)
Four configurable digital status outputs through 24 V, 30 W relays
Four configurable digital status outputs through 110 V relays
Remote pressure/flow sensors
Analogue speed control
Pump drives 730SN 730UN 730DuN 730BpN 730US 730DuS 730EnN 730PnN
Fully configurable inputs; 0-10 V or 4-20 mA
Analogue outputs; 0-10 V, 4-20 mA
Keypad/analogue input scaling (replacement of diaphragm pumps)
Tacho frequency output; 0-1478 Hz
2x sensor inputs 4-20 mA*
Security
Pump drives 730SN 730UN 730DuN 730BpN 730US 730DuS 730EnN 730PnN
3-level security PIN lock
Network communication
Pump drives 730SN 730UN 730DuN 730BpN 730US 730DuS 730EnN 730PnN
RS485 network control
Digital pump commands (Profibus / EtherNet/IP)
Pump drives 730SN 730UN 730DuN 730BpN 730US 730DuS 730EnN 730PnN
PROFIBUS® DP V0
PROFINET® (CC-B & Netload Class III)
EtherNet/IP™
Communication speeds from 9.6 kbits/s up to 12000 kbits/s
Network speed: 10/100 Mbps - Full Duplex Operation
Network speed: 100 Mbps - Full Duplex Operation
Auto-detect bus speed
Speed set point
Speed feedback
Flow calibration function
Hours run
Revolution counter
Leak detection
Low fluid level alarm
Diagnostic feedback
Flow Totaliser
Sensor scaling
Dispensing (Network Control)

*Range of 3rd party pressure/flow sensors supported—see compatible sensor list on www.wmftg.com/literature

Literature

Brochures

  1. Sanitary process pumps (US).pdf
    PDF - 2.3mb
  2. Sanitary process pumps (EN).pdf
    PDF - 2.1mb
  3. Industrial process pumps (US).pdf
    PDF - 1.4mb
  4. Ethernet IP (EN).pdf
    PDF - 241.6kb
  5. Ethernet IP (US).pdf
    PDF - 242.4kb
  6. Industrial process pumps (EN).pdf
    PDF - 1.4mb

Datasheet

  1. 730 datasheet (EN).pdf
    PDF - 547.7kb
  2. 730 datasheet (EN).pdf
    PDF - 547.7kb

Manuals

  1. 730 BpN manual (EN).pdf
    PDF - 3.1mb
  2. 730 EnN manual (EN).pdf
    PDF - 3.8mb
  3. 730 DuN manual (EN).pdf
    PDF - 4.6mb
  4. 730 PnN manual (EN).pdf
    PDF - 3.7mb
  5. 730 UN manual (EN).pdf
    PDF - 4.7mb
  6. 730 BpN manual (EN).pdf
    PDF - 3.1mb
  7. 730 PnN manual (EN).pdf
    PDF - 3.7mb
  8. 730 UN manual (EN).pdf
    PDF - 4.7mb
  9. 730 EnN manual (EN).pdf
    PDF - 3.8mb
  10. 730 SN manual (EN).pdf
    PDF - 2.9mb
  11. 730 DuN manual (EN).pdf
    PDF - 4.6mb
  12. 730 SN manual (EN).pdf
    PDF - 2.9mb

Other Resources

  1. Watson-Marlow 530, 630, 730 EtherNet-IP™ and PROFINET® compatible sensor list (EN).pdf
    PDF - 246.8kb
  2. Industrial EtherNet flyer (US).pdf
    PDF - 314.6kb
  3. Industrial EtherNet flyer (EN).pdf
    PDF - 293.4kb
  4. Watson-Marlow 530, 630, 730 EtherNet-IP™ and PROFINET® compatible sensor list (EN).pdf
    PDF - 246.8kb
  5. 530,630,730 EtherNet IP EDS compatibility guide.pdf
    PDF - 68.6kb
  6. 530,630,730 PROFINET® compatibility guide.pdf
    PDF - 65.7kb
  7. 530,630,730 PROFINET® compatibility guide.pdf
    PDF - 65.7kb
  8. 530,630,730 EtherNet IP EDS compatibility guide.pdf
    PDF - 68.6kb
  1. gsdml-v2-4-watson-marlow-530-630-730-profinet-pump-20211116.zip
    ZIP - 5.6kb
  1. 530,630,730 Ethernet IP EDS Rev 2.1.eds
    EDS - 111.2kb
  2. 530,630,730 Ethernet IP EDS Rev 2.2.eds
    EDS - 113.3kb
  3. 530,630,730 Ethernet IP EDS Rev 2.2.eds
    EDS - 113.3kb
  4. 530-630-730-EtherNetIP-pump-rev-2.5.eds
    EDS - 113.9kb
  5. 530,630,730 Ethernet IP EDS Rev 2.1.eds
    EDS - 111.2kb
  1. PROFIBUS (GSD) 530-630-730 control file.gsd
    GSD - 2.6kb
  2. PROFIBUS (GSD) 530-630-730 control file.gsd
    GSD - 2.6kb
  1. GSDML-059F-0001-WMPEPSI-01.bmp
    BMP - 8.4kb

Pumpheads

720R and 720RX continuous tubing pumpheads

  • 720R pumpheads accommodate 4.8 mm wall continuous tubing for joint-free flow from source to discharge. Available in five bore sizes: 9.6 mm, 12.7 mm, 15.9 mm 19.0 mm and 25.4 mm, giving up to 2,000 L/h (8.8 GPM) flow at up to 2 bar (30 psi) pressure.
  • 720RX extension pumpheads offer identical performance, but at a maximum pressure of 1 bar (15 psi).

Tubing is available in five materials for almost any chemical requirement.

720RE and 720REX LoadSure tubing element pumpheads

  • 720RE pumpheads accommodate 4.8 mm-wall LoadSure tubing elements in two conformations: with PVDF Tri-clamp-style connectors for sanitary applications; and with industrial Cam-and-Groove connectors. Both are offered in four bore sizes: 12.7 mm, 15.9 mm, 19.0 mm and 25.4 mm, giving up to 2,000 L/h (8.8 GPM) flow at up to 2 bar (30 psi) pressure.
  • 720REX extension pumpheads offer identical performance, but at a maximum pressure of 1 bar (15 psi).

Elements are available in Pumpsil platinum-cured silicone, Bioprene and STA-PURE PCS for sanitary applications; and in Marprene, Pumpsil and Neoprene for industrial use.

Drives

Simple-to use HMI requiring minimal key presses to reduce chances of costly errors. Flow proportional to pump speed over 3,600:1 control range. IP66 NEMA 4X cased pumps for washdown environments.

  • 730SN simple, plug-in and switch on pumps offering economy of ownership. Ultimate process security with a 3 level PIN lock.
  • 730UN with all the features of the SN models, plus configurable inputs and outputs.
  • 730DuN with configurable inputs and outputs, plus RS232 and RS484.
  • 730BpN with real time communication makes your process secure and flexible. Bus speed 9.6 kbits/s up to 12,000 kbits/s connectivity
  • 730EnN EtherNet/IP connectivity for fast and easy access to pump data over Industrial Ethernet
  • 730PnN PROFINET connectivity for fast and easy access to pump data over Industrial Ethernet

Order Information

Product codes

Drive with 720R Pumphead product codes

Continuous tubing for 720R
9.6 mm 12.7 mm 15.9 mm 19 mm 25.4 mm
Marprene® 902.0096.048 902.0127.048 902.0159.048 902.0190.048 902.0254.048
Pumpsil® 913.A096.048 913.A127.048 913.A159.048 913.A190.048 913.A254.048
Bioprene® 933.0096.048 933.0127.048 933.0159.048 933.0190.048 933.0254.048
PureWeld® XL 941.0096.048 941.0127.048 914.0190.048 914.0254.048
STA-PURE® Series PCS 961.0096.048 961.0127.048 961.0159.048 961.0190.048 961.0254.048
Neoprene 920.0127.048 920.0159.048 920.0190.048 920.0254.048

Drive with 720RE Pumphead product codes

LoadSure elements for 720RE
Sanitary LoadSure elements, Tri-clamp style PVDF connectors Industrial LoadSure elements, Cam & Groove PP connectors
Element tubing 3/4 " 1 " 3/4 " 1 "
12.7 mm 15.9 mm 19.0 mm 25.4 mm 12.7 mm 15.9 mm 19.0 mm 25.4 mm
Marprene® 902.0127.PPC 902.0159.PPC 902.0190.PPC 902.0254.PPC
Pumpsil® 913.A127.PFT 913.A159.PFT 913.A190.PFT 913.A254.PFT 913.A127.PPC 913.A159.PPC 913.A190.PPC 913.A254.PPC
Bioprene® 933.0127.PFT 933.0159.PFT 933.0190.PFT 933.0254.PFT
STA-PURE® Series PCS 961.0127.PFT 961.0159.PFT 961.0190.PFT 961.0254.PFT
Neoprene 920.0127.PPC 920.0159.PPC 920.0190.PPC 920.0254.PPC

Drive with 720R/RX Pumphead product codes

Continuous tubing for 720RX
9.6 mm 12.7 mm 15.9 mm 19 mm 25.4 mm
Marprene® 902.0096.048 902.0127.048 902.0159.048 902.0190.048 902.0254.048
Pumpsil® 913.A096.048 913.A127.048 913.A159.048 913.A190.048 913.A254.048
Bioprene® 933.0096.048 933.0127.048 933.0159.048 933.0190.048 933.0254.048
PureWeld® XL 941.0096.048 941.0127.048 914.0190.048 914.0254.048
STA-PURE® Series PCS 961.0096.048 961.0127.048 961.0159.048 961.0190.048 961.0254.048
Neoprene 920.0127.048 920.0159.048 920.0190.048 920.0254.048

Drive with 720RE/REX Pumphead product codes

LoadSure elements for 720REX
Sanitary LoadSure elements, Tri-clamp style PVDF connectors Industrial LoadSure elements, Cam & Groove PP connectors
Element tubing 3/4 " 1 " 3/4 " 1 "
12.7 mm 15.9 mm 19.0 mm 25.4 mm 12.7 mm 15.9 mm 19.0 mm 25.4 mm
Marprene® 902.0127.PPC 902.0159.PPC 902.0190.PPC 902.0254.PPC
Pumpsil® 913.A127.PFT 913.A159.PFT 913.A190.PFT 913.A254.PFT 913.A127.PPC 913.A159.PPC 913.A190.PPC 913.A254.PPC
Bioprene® 933.0127.PFT 933.0159.PFT 933.0190.PFT 933.0254.PFT
STA-PURE® Series PCS 961.0127.PFT 961.0159.PFT 961.0190.PFT 961.0254.PFT
Neoprene 920.0127.PPC 920.0159.PPC 920.0190.PPC 920.0254.PPC

Recommended Products

  1. Marprene tubing

    Marprene tubing

    Thermoplastic elastomer tubing especially resistant to oxidizing agents. 5 ºC to 80 ºC (23 ºF to 176 ºF) to 7 bar (100 psi).

    Tubing - peristaltic

  2. Pumpsil tubing

    Pumpsil tubing

    Platinum-cured silicone tubing with ultra smooth bore and excellent flow stability. -20 ºC to 80 ºC (-4 ºF to 176 ºF).

    Tubing - peristaltic

  3. Bioprene - Thermoplastic tubing

    Bioprene - Thermoplastic tubing

    Thermoplastic tubing with long peristaltic life and low permeability. 5 ºC to 80 ºC (23 ºF to 176 ºF).

    Tubing - peristaltic

Related Products

  1. 100 series cased pump

    100 series cased pump

    Flow rates to 190 ml/min (3.04 USGPH) and pressures up to 2 bar (30 psi). Speed control up to 10,000:1.

    Pumps - cased pumps

  2. 200 series cased pump

    200 series cased pump

    Flow rates from 6 μl/min to 22.0 ml/min. Multi-channel cassette pumps with up to 32 channels

    Pumps - cased pumps

  3. 300 series cased pump

    300 series cased pump

    Flow rates from 2 μl/min to 2,000 ml/min and pressures up to 2 bar (30 psi). Single or multi channel.

    Pumps - cased pumps

  4. 530 process pumps

    530 process pumps

    Flow rates to 3.5 L/min (55 USGPH) and pressures up to 7 bar (100 psi). Precise 2,200:1 speed control range.

    Pumps - cased pumps

  5. 630 mid-flow process pumps

    630 mid-flow process pumps

    Flow rates to 18 L/min (4.76 USGPM) and pressures up to 4 bar (60 psi). Precise 2,650:1 speed control range.

    Pumps - cased pumps

Our process pump specialists are here to help you succeed.

To order a product or ask a question

Contact our experts